Foundry Powders

Estimated Shipping Time After Processing | 24 to 48 Hours

SKU: Foundry Powders Category: Tag:

PARTING POWDER
Parting Powder is an Alumino Silicate refractory powder with a size grading similar to baking
flour (200#)
The powder is given a waterproof non-hygroscopic coating to prevent moisture pick. Parting
powder is dusted onto a pattern loosely to give complete coverage. Once the sand is packed
onto the pattern the Parting Powder acts as a Separating Agent preventing the pattern and the
sand from sticking to one another.
Loose Parting powder is blown off the mould and pattern. Any Parting Powder adhering to the
mould is not detrimental to the mould, to the coatings applied to the mould, nor the metal
entering the mould cast.
Packaging
25kg Bags


FIRE CLAY POWDER
PARTICLE SIZE:
200 #
MOISTURE CONTENT:
3.9 %
TYPICAL CHEMICAL ANALYSIS
Si02 46.83%
Ti02 2.05%
AL203 36.26%
Fe203 2.04%
Mn0 0.02%
Mg0 0.28%
K20 0.24%
Loi 12.53%
NOTICE:
The information contained herein is correct to the best of our knowledge. Procor Steel Traders
disclaims any warranties as to the accuracy of the same. Recommendations or suggestions are
made without guarantee or representation as to result since conditions of use are beyond our
control. The Buyer shall conduct his own test to determine the stability of such product for
buyer purposes.
All data listed is average and typical


BENTONITE OCEAN
BENTONITE OCEAN NATURAL CIVIL ENGINEERING GRADE
% %
SiO² 60.9 55.8
Al²O³ 15.7 17.9
Fe²O³ 6.4 7.1
CaO 2.1 1.9
MgO 0.6 0.2
Na²O 1.9 6.1
K²O 1.5 1.8
LOSS ON IGNITION 7.9 6.7
MOISTURE 4.8 7.8
PH 8.5 9.9
SWELLING 4 ml / gm 10 ml / gm
VISCOSITY AT 600 RPM (CP) 25 51
PERCENT OF WYOMING
BENTONITE FOR COMPARISON
80 90
SIEVE ANALYSIS
RETENTION 38 MICRONS 3 3
RETENTION 15 MICRONS 40 4


BENTONITE
 Occupational Health and Safety Act and Regulations (85/1993)
 General Administrative Regulations

1. PRODUCT AND COMPANY IDENTIFICATION
Trade Name: Bentonite
Chemical Family: N/A
Chemical Name: Crystalline quartz (naturally occurring contaminant)
Synonyms: N/A
Chemical Abstract no: 1302-78-9
NIOSH No: N/A
UN no: N/A

2. COMPOSITION
Hazardous components: Naturally occurring hydrated alumino-silicate of sodium, calcium, magnesium and
iron
EEC Classification: N/A
R Phrases: N/A

3. HAZARDS IDENTIFICATION
Main Hazard: This clay product contains a small amount of crystalline silica, which may cause delayed
respiratory disease if inhaled over a prolonged period of time. Avoid breathing dust.
Flammability: Inorganic mineral – Non-flammable
Chemical hazard: None
Biological hazard: No known effect
Reproduction hazard: No known effect
Eye effects: Causes redness and pain
Health effects – skin: Develops alkaline properties when wet, which may cause skin irritation or burns
Health effects – ingestion: None
Health effects – inhalation: May cause delayed respiratory disease if dust inhaled over a prolonged period
of time. Excessive inhalation of dust may result in shortness of breath and reduced pulmonary function
Carcinogenicity: No known effect
Mutagenicity: No known effect
Neurotoxicity: No known effect

4. FIRST-AID MEASURES:
Product in the eye: Rinse well with water and refer to doctor if irritation persists
Product on skin: Rinse well with water and refer to doctor if irritation persists
Product ingested: None
Product inhaled: Remove to fresh air. Give oxygen or artificial respiration if necessary. Get medical
attention

5. FIRE-FIGHTING MEASURES:
Extinguishing media: None
Special hazards: None
Protective Clothing: None

6. ACCIDENTAL RELEASE MEASURES:
Personal Precautions: Avoid breathing dust. Wear an approved respirator.
Environmental precautions: None
Small spills / Large spills: Vacuum if possible to avoid generating airborne dust. DO NOT ADD WATER,
the product will become slippery when wet
2 | P a g e

7. HANDLING AND STORAGE
Suitable material: N/A
Handling/storage precautions: Avoid breathing dust. Use NIOSH/MSHA approved respirator where TLV
limits for crystalline silica may be exceeded. Slippery when wet

8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Occupational exposure limits: No data available
Engineering control measures: Adequate dust control and dust extraction systems
Personal protection – respiratory: Use NIOSH/MSHA approved respirator
Personal protection – hand: Not required
Personal protection – eye: Safety goggles
Personal protection – skin: Overalls and barrier cream
Other protection: Use good housekeeping practices

9. PHYSICAL AND CHEMICAL PROPERTIES:
Appearance: Pale grey to buff (light
brown) powder or granule
Explosive properties: None
Odour: Odourless Oxidizing properties: None
pH: 8 – 10.5 Vapour pressure: N/A
Boiling point: N/A Density: N/A
Melting point: N/A Solubility – water: Negligible
Flashpoint: N/A
Flammability: N/A
Solubility – solvent: N/A
Solubility – coefficient: N/A
Auto flammability: N/A

Foundry Powders

D10 Plaster 25kg, Part Powder 25kg, Fire Clay (Powder) 25kg, Bentonite Ocean 25kg, Coal Dust 40kg, Starch 25kg